Bezmel
11.06.2010, 12:45
Epson 7600 выдает ошибку 00010005. Каретка застряла по середине. Что деалть?
Нажмите, чтобы перейти к полной версии темы: : Epson 7600 выдает ошибку 00010005. Каретка застряла по середине.
Starik Kramer
13.06.2010, 03:07
Данная ошибка означает сбой в работе сервопривода, который перемещает печатающую голову.
Причин может быть несколько, для вас наиболее благоприятная – случайное препятствие на пути движения головы, либо попадание мусора в механизм принтера. В худшем случае это может быть серьезная поломка мотора и платы управления – без сервисного специалиста вы ее вряд ли устраните.
Если владеете техническим английским, вот подробное описание:
Service Call 00010005
Description
CR Motor is out of step.
Explanation
The printer causes this error and stops operation if it cannot detect the specified length
encoder pulse signals within a fixed time period or when abnormally long
or short pulse signals are detected while the CR Motor is rotating.
Possible Causes
The connector of the Cutter Solenoid is disconnected.
The fuse for the Solenoid is blown. (on the Main Board)
CR Motor failure
The CR Motor driver is damage. (42 V is shorted)
The temperature fuse of the Cutter Solenoid is blown (the Cutter Solenoid
does not work and the Carriage cannot be unlocked.)
Check Point
1. Make sure that the Timing Fence is securely attached on the CR Encoder.
2. Make sure that the CR Encoder and the Timing Fence are free of dust or
foreign materials.
3. Perform the Encoder check by the “1.4.6.1 Self Testing Menu (SELF
TESTING)” (p.106).
4. Make sure that the CR Timing Belt is normal and its tension is appropriate.
5. Perform the CR HP Sensor check by the “1.4.6.1 Self Testing Menu (SELF
TESTING)” (p.106).
6. Make sure that the Carriage moves smoothly without any abnormal load.
7. Make sure that the CR Motor is not shorted out.
If it does, replace the C594 Main Board together with the PF Motor.
8. Make sure that the harnesses are connected correctly and not broken.
Remedy
1. Reattach the Timing Fence for detecting the encoder securely and correctly.
2. Clean dirt or paper dust on the Timing Fence and check if it is damaged.
3. Reconnect the Cutter Solenoid connector securely and correctly.
Причин может быть несколько, для вас наиболее благоприятная – случайное препятствие на пути движения головы, либо попадание мусора в механизм принтера. В худшем случае это может быть серьезная поломка мотора и платы управления – без сервисного специалиста вы ее вряд ли устраните.
Если владеете техническим английским, вот подробное описание:
Service Call 00010005
Description
CR Motor is out of step.
Explanation
The printer causes this error and stops operation if it cannot detect the specified length
encoder pulse signals within a fixed time period or when abnormally long
or short pulse signals are detected while the CR Motor is rotating.
Possible Causes
The connector of the Cutter Solenoid is disconnected.
The fuse for the Solenoid is blown. (on the Main Board)
CR Motor failure
The CR Motor driver is damage. (42 V is shorted)
The temperature fuse of the Cutter Solenoid is blown (the Cutter Solenoid
does not work and the Carriage cannot be unlocked.)
Check Point
1. Make sure that the Timing Fence is securely attached on the CR Encoder.
2. Make sure that the CR Encoder and the Timing Fence are free of dust or
foreign materials.
3. Perform the Encoder check by the “1.4.6.1 Self Testing Menu (SELF
TESTING)” (p.106).
4. Make sure that the CR Timing Belt is normal and its tension is appropriate.
5. Perform the CR HP Sensor check by the “1.4.6.1 Self Testing Menu (SELF
TESTING)” (p.106).
6. Make sure that the Carriage moves smoothly without any abnormal load.
7. Make sure that the CR Motor is not shorted out.
If it does, replace the C594 Main Board together with the PF Motor.
8. Make sure that the harnesses are connected correctly and not broken.
Remedy
1. Reattach the Timing Fence for detecting the encoder securely and correctly.
2. Clean dirt or paper dust on the Timing Fence and check if it is damaged.
3. Reconnect the Cutter Solenoid connector securely and correctly.